Category Archives: General

Articles about Amateur Radio and the Nashua Area Radio Society. This is a general category which includes most articles on our website.

Activities, Featured, General

October POTA Activation October 15th – Mount Kearsarge

2 Comments

October’s POTA activation will bring us back to Winslow State Park on the flanks of Mount Kearsarge. This park has a huge picnic area that we have used in the past . I’ve personally talked to the ranger in charge so she knows us and she loves hams!  The plan is to meet at the Winslow trail parking area this is at the end of Winslow House road also known as Kearsarge Mountain rd In Warner at 11 am on October 15th .  Here is a link to a map detailing the area. In addition the route is well signed from the highway to destination  so it’s an easy to follow drive.

You’ll also want to go to the NH State parks website to get a parking pass. Here is a link to The NH State Parks page where you can get that pass. In addition you’ll want to bring a fleece jacket and rain jacket, bug spray, sun block and a picnic lunch if you’d like. Also bring your  HT if you have one.We’ll be at a higher altitude so you might like to get a few VHF/UHF contacts as well.

Mount Kearsarge POTA
typical POTA setup

This is a POTA mentoring event so we will have multiple stations and antennas setup on different bands with a POTA coach at each one quite similar to a field day setup. If this is your introduction to POTA (Parks on The Air) fear not we can answer your questions and help you get on the air. All that’s needed is a willingness to learn. You don’t even need a ham radio license the coaches can be the control operator so bring an unlicensed friend!

If you have a mobile rig we will be listening to the N1IMO network of repeaters and  146.52 as well for chatting on our way up. If you have a GPS the physical address is 475 Kearsarge Mountain Rd. Wilmot, NH 03287. Make sure your GPS doesn’t try to default to another town. There are multiple towns in the area with Kearsarge Mountain in the name . If you have any questions email me and I can send more detailed instructions. It would be a good idea to email me anyway so we can get an idea of how many people to expect. My email is [email protected].

Hope to see you at the Mount Kearsarge POTA!

73′

Jim K1BRM

Activities, General, Station Equipment

Using My “Shack-In-A-Box” on a POTA Activation

Recently, I was asked not only how I made out during the Nashua Area Radio Society’s Sep 3, 2023 Club POTA activation from Rollins State Park (K-2676) and Kearsarge Mountain State Forest (K-4918) (it’s a two-fer), but what the gear was that I used.  So I decided to “pen” an article with some of the details.

The Box

Jay Francis, KA1PQK and I decided to put my go-box to the test in the field during this activation.  It is an unassuming, little old “shack in a box”… although it is a large box… a large dayglow yellow box. So, maybe it isn’t all that little or unassuming after all.  But I digress.

Apache 4800 for POTA
My unassuming go-box (the name plate in the center came from HamCrazy.com)

The go-box itself is built around Harbor Freight’s largest protective waterproof ABS case, the Apache 4800. Despite its size, the case lends itself to portability.  I literally only need to grab it and my trusty modified Lenovo N23 Chromebook (more on that later) and head out the door. I’ve used this same model Apache case to ship photographic gear all over the country.  It works exceptionally well at protecting my gear at roughly 1/2 to 1/3 the cost of a similar Pelican case. I like that, after all, I am a ham.

The go-box contains everything else I will need for an activation in any mode…  SSB, CW, or digital. Altogether, the go-box weighs in at around 8 pounds… light enough to easily deploy to most places, but heavy enough that I don’t want to hike with it for a SOTA activation.

The Station

The Radios

The station itself is designed around a Xiegu G90 SDR Transceiver. The G90 is a 20w, all mode, 10-160m SDR radio with some incredible features for such a reasonably priced rig. It has a built-in antenna tuner that will match nearly anything you can throw at it, a (small but useful) waterfall display, DSP noise reduction, etc.  The G90 is powered by a Talentcell rechargeable 12V 6000mAh Lithium-ion battery pack. While intended to charge cell phones via it’s 5v USB ports, the Talentcell has a very convenient 12v output port as well, and provides me with up to 2.5 hours of operating at reasonable output power for the radio.

For SSB, I use the stock Xiegu mic that came with the G90.  Surprisingly, for a $450 rig, I have received several positive comments on audio quality! For CW, I use a CW Morse paddle.  It is small, but hefty enough that it won’t move around the table when I am using it. As the G90 requires additional hardware for digital interfacing, I use a Xiegu CE19 digital interface kit connected to a Raspberry Pi 4b to allow me to operate FT8, RTTY, and other digital modes.

Finally, I have the Xiegu OEM CI-V USB cable that connects the radio to the Pi allowing for rig control and automatic frequency capture in the various software apps that I use.  Xiegu radios use the ICOM CI-V protocols for rig control, which makes them (generally) easy to set up and use.

The go-box also contains a QYT dual band mobile FM radio, powered by an external battery.  However, we did not use this radio on the activation.

The Antennas

All the RF is forced out of the radio into an MFJ-1899T portable vertical (which also lives in the Apache case when stored). The antenna  attaches at the back of the rig to a right-angle connector with a PL259-to-BNC adapter on it.  I also have a premeasured and marked counterpoise connected to the G90’s ground point that I deploy to improve the signal.

Jay brought his portable vertical setup as well.  It’s an MFJ 2286 portable 7-55MHz antenna on a Husky telescoping tripod.  We switched antennas from the 1899T to Jay’s 2286 roughly halfway through the activation.  Although I don’t have any empirical data, and my memory is like that of a 130-year-old, I recall that Jay’s vertical worked quite a bit better.  No surprise, given that the 1899T is a true compromise antenna.  But it does make Q’s.

WE1H go-box bottom
View of the bottom of the go-box containing the radios and stored antenna.

The Computer

The Pi is powered separately from the radio’s power source by an Iniu 10,000 mAh 5v battery and can run for 6 or so hours on a single charge.  As the Pi’s integrated audio hardware is insufficient for use with digital modes, I use an inexpensive Sabrent USB audio dongle which works nicely. For time synchronization, I either manually update the time on the Pi (as was the case on this POTA activation) or use a U-Blox USB GPS dongle connected to the Pi for a GPS time source.  I did bring a new solar charger setup with me on this activation, but never deployed it.

The Software

The software on the Pi is a critical part of the entire solution, without which, the whole “shack in a box” concept goes out the window (ask me how I know this).  At the base is the Raspberry Pi O/S, which I built from KM4ACK’s awesome Build-a-Pi solution. Although BAP is being replaced by 73 Linux, it is still an excellent quick deployment solution for a Raspberry Pi.  The Pi contains a host of software applications that you would find in any shack, as well as some that are specifically EMCOMM related, and some that facilitate portable operation.  I’ll go through what we used during the activation and leave the other details for a future article perhaps.

The Pi also has a hot-spot solution that auto starts when no known network is detected.  The hot-spot is the real key to the overall shack-in a box solution though… but more on that later. For rig control, FLRig is my go to – it allows FLDigi, WSJT, and my logging program, CQR Log, to have connectivity to the radio.  When operating SSB or CW, I simply fire up CQR Log and it starts FLRig, which connects to the radio, and I am off to the races.  If I am instead  operating digital using WSJT or FLDigi, I need only to tell CQR Log to start either program, and it seamlessly connects and shares QSO data (I say seamlessly now, not so much until I truly figured out how to integrate the software pieces… but that’s for another article too).

WE1H go-box top view
View of the top of the go-box case. All of the components are secured to the  top by industrial strength Velcro fasteners. Some improvements were made post-activation to control the cables and wires better, and clean things up.

The “Other” Computer

Truly attentive readers may have noticed something missing though…  a screen with which to view the Pi desktop.  That’s kind of important.  This is where the hot-spot feature of the Pi is really handy.  It’s also where my Lenovo Chromebook comes into play.  Although in reality, the Lenovo is no longer a Chromebook per se, but more of a “Linuxbook”.  I removed Chrome from it and installed Debian Linux instead. There are videos on YouTube as to how to do this.  It’s a great way to “rehab” an outdated Chromebook that cost $7 on eBay, and Linux is a great choice for portable ops as it is so much more flexible than Windows (in my opinion).  I use the Linuxbook to VNC into the Pi and view the desktop.  It is a slick solution that I admittedly copied from others.  Any device with a VNC software app can be used, provided it can connect to the Pi’s hot-spot network (you do however need to know the password to the hot spot, which I now have written down).  This includes Windows systems, iOS devices, Linux devices, Android devices, etc. In a real EMCOMM situation, that level of flexibility is nice.

The decision to include a Pi in the go-box was a simple one for me…  having a preconfigured hardware / software solution with all of my apps in a single self-supporting enclosure requiring only a VNC capable device to operate it seemed like a pretty cool idea.  So far, barring some experimentation and poor decision making by yours truly, it has proven mostly reliable.

Results

So, how did it do during the activation?  We made 23 QSO’s running anywhere from 5 to 20 watts:  21 FT8, and 2 SSB.  We contacted hunters all over the country…  TX, OK, MS, NC, SC, IL, NH, GA, and even a DX station in England.  Several park-goers stopped and talked to us about what we were doing, and we got to explain Ham Radio and POTA to a number of them.  While it certainly proved a useable solution for the activation, I am constantly looking at ways to refine it and make it better and more “bullet proof”.

Deployed WE1H go-box POTA
The “fully deployed” box ready for operating.

Here are some links to the various components of the go-box in case you are interested in more details:

Apache 4800 case: https://www.harborfreight.com/4800-weatherproof-protective-case-x-large-yellow-56865.html

Xiegu G-90: https://www.hamradio.com/detail.cfm?pid=H0-016772

Raspberry Pi 4b: https://www.raspberrypi.com/products/raspberry-pi-4-desktop-kit/

Sabrent USB Audio: https://www.amazon.com/gp/product/B00IRVQ0F8/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

KM4ACK Build-a-Pi: https://github.com/km4ack

WSJT: https://wsjt.sourceforge.io/wsjtx.html

FLDigi: http://www.w1hkj.com/

CQR Log: https://www.cqrlog.com/

U-Blox GPS: https://www.amazon.com/gp/product/B00NWEEWW8/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

MFJ 1899T Antenna: https://mfjenterprises.com/products/mfj-1899t

MFJ 2286 Antenna: https://mfjenterprises.com/products/mfj-2286

Husky K40366 Tripod: https://www.homedepot.com/p/Husky-Universal-Telescoping-Tripod-K40366/319012088

Iniu Battery https://www.amazon.com/gp/product/B08MBQS368/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1

Talentcell Battery: https://www.amazon.com/gp/product/B00ME3ZH7C/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Apache case ID tag: https://www.hamcrazy.com/index.php?main_page=index&cPath=44

If you decide to build your own go-box, have fun, get creative, and post some pics on the N1FD.org site!

Featured, General, Station Equipment

Fun with the Clear Sky Institute HamClock

I haven’t had the occasion to use any programming languages since retirement. That’s why the addition of a Raspberry Pi 4 Model B to the shack was a welcome change. I like to think of the Raspberry Pi as just another computer – one that uses a different operating system. With the Raspberry Pi, I can browse the Internet, access email, and write and run programs.

When I began to assemble a shack, I reserved a space on the wall for a 32″ TV, Figure 1, which was purchased during a temporary rental stay. That TV has been unused for 3 years, but it was earmarked for a HamClock.

Figure 1. Unused 32″ TV Earmarked for HamClock. The TV was wall-mounted above the shack monitors. Please click on image to expand.

I searched the N1FD site to see if anyone had written about HamClock, but no articles were found. The first article for HamClock, written by Elwood Downey, WB0OEW, appeared in October 2017 QST[1]. In his article, he calls for the use of an Adafruit HUZZAH ESP8266 Wi-Fi system-on-chip. That device was fastened to the back of a 7″ TFT display.

The version of HamClock that I built for use with the 32″ HDTV employs the Raspberry Pi 4 Model B, Figure 2, with 2 GB memory[2]. The kit that I found on Amazon includes a 64 GB microSD card (with USB adapter) onto which the Raspberry Pi operating system had been preloaded. The kit also includes a plastic case with fan, little rubber feet, tiny screws to attach a camera, device heatsinks, a wall-wart power supply, a micro HDMI to HDMI cable, an instruction manual and various assembly instruction cards. The user has to provide their own USB mouse and keyboard. I already owned a wireless mouse and keyboard so I was able to use a single USB 2.0 port on the Pi for the wireless adapter.

If you already have a microSD memory card with USB adapter, power supply, mouse, keyboard and HDMI cable, you could get by with a Raspberry Pi Zero[3] at one-fourth the price.

Figure 2. Raspberry Pi 4 With Wireless Mouse and Keyboard. A single USB 2.0 port on the Pi is used for the wireless adapter leaving 1 x USB 2.0 and 2 x USB 3.0 ports unused. Power and HDMI cables are visible. Please click on image to expand.

If your Raspberry Pi does not come equipped with the operating system installed, you can download it from the official Raspberry Pi website and store it on a microSD card for installation provided that you have a USB to microSD card adapter. The Raspberry Pi site allows you to select an operating system and it allows you to specify where the operating system will be stored upon download:

https://www.raspberrypi.com/software/

Please, follow the directions to install the operating system on your device.

I noticed an ambiguity in the kit documentation regarding connection of the cooling fan to the Pi bus header. A tiny drawing, Figure 3, shows where the red and black leads should be connected, namely pins 1 and 14, respectively. The documentation should make it clear that the long header row that contains pin 1 contains all of the odd-numbered pins while the long header row that contains pin 14 contains all of the even-numbered pins. This makes it a bit easier to locate pin 14.Figure 3. Location of the Fan Voltage Pins. The long header row that contains pin 1 contains all of the odd-numbered pins while the long header row that contains pin 14 contains all of the even-numbered pins. Please click on image to expand.

The instructions advise that the HDMI port closest to the DC power supply input be employed if only one monitor will be used. I was confused about the power supply connector. It may be plugged into the Pi upside down. However, I found that a bright flashlight can be used to look inside the power supply connector and inside the Pi power supply input jack to ensure that the conductive contacts face one another. If the connector has been plugged in correctly, some LED status lights on the Pi circuit card should illuminate once the inline DC power cord switch, Figure 4, has been turned on.

This switch has to be used with caution. The operating system, if running, must be shut down prior to turning the DC power switch to the off position. Failure to do so could corrupt data stored in memory and on the microSD card. This is a minor weakness in the design.

Figure 4. The Inline DC Power Switch. The operating system must be shut down from the Raspberry Pi menu icon on the taskbar before turning the DC power switch to the off position. Please click on image to expand.

Two methods may be used to shut down the Raspberry Pi. There is a Raspberry icon that appears on the taskbar. One of the drop-down selections is to log out. Once selected, another dropdown appears that offers the choice to shutdown or reboot. There is a second method that permits shutdown from a terminal window, Figure 5, which may be opened from the taskbar. One need only enter the command:

sudo shutdown -h now

to close the operating system. A third option is to add a momentary switch to the Pi bus header. That may be used to assert a shutdown command for the operating system. I have not implemented that feature.

Figure 5. Terminal Window. A terminal window may be opened from the Pi taskbar. Please click on image to expand.

Once an unused HDMI input to the monitor or TV is selected, and the mouse, keyboard and HDMI cable are plugged in, the power switch in the supply power cord may be switched on. Within seconds the Raspberry Pi logo appears followed by a series of questions that include language and time zone. The operating system will also ask for access to WiFi. I found that WiFi was easier than connecting another Ethernet cable to the access point.

Once WiFi is connected, the operating system will update. Finally, a desktop appears. The taskbar was docked to the top of the screen, but I moved it to the bottom because that is where I am used to seeing it, Figure 6. That may be accomplished by selecting that feature from the Raspberry Pi icon on the taskbar. The operating system provides access to the Internet via a browser icon that appears on the taskbar. There are also icons for a terminal window and Bluetooth.

Figure 6. Taskbar Moved and Docked to the Bottom of the Screen. This may be selected from screen appearance under the Raspberry Pi icon on the taskbar. Wallpaper like this may be selected from a list. Please click on image to expand.

The Raspberry Pi icon, Figure 7, provides several selections for screen appearance, resolution and the usual accessories. It also provides a means for shutting down the operating system.

Figure 7. Menu Provided Under Raspberry Pi Accessible from Taskbar. Access to many options is provided here including Raspberry Pi screen resolution. This is not the same as the HamClock screen resolution setting, which will be selected separately. Please click on image to expand.

It was learned that the means for capturing screenshots within the Pi operating system is Print Screen (PrtSc) just as it is in Windows, so this method has been used to illustrate this article. The images are stored as PNG files in the home Raspberry Pi folder, not under Screenshots in the Photo folder where one would expect them to be.

After opening a terminal window, I followed the directions provided at the Clear Sky Institute[4] web page under the Desktop tab with some notable exceptions. First, I took the advice of KM4ACK[5] to circumvent error messages by executing two scripts before attempting anything else. These scripts may be found listed under the Desktop tab under the subsection titled “To install HamClock on other UNIX-like systems follow these steps”, paragraph 2, “If you get errors”[6]. These steps at Clear Sky are correct except for a syntax error pointed out by KM4ACK[7] in the script:

sudo apt-get -y curl install make g++ libx11-dev xserver-xorg raspberrypi-ui-mods libraspberrypi-dev linux-libc-dev lightdm lxsession openssl

This script must be corrected so that the word ‘install’ precedes the word “curl”. The corrected script should read:

sudo apt-get -y install curl make g++ libx11-dev xserver-xorg raspberrypi-ui-mods libraspberrypi-dev linux-libc-dev lightdm lxsession openssl

I don’t know why this has not been corrected on the Clear Sky Institute web page, but I am happy that KM4ACK pointed it out.

We may now follow the steps listed under “To install HamClock on a Raspberry Pi follow these steps”. It is suggested that the lines of code be executed line-by-line.

cd
curl -O http://www.clearskyinstitute.com/ham/HamClock/install-hc-rpi
chmod u+x install-hc-rpi
./install-hc-rpi

If you choose not to install a desktop icon, you may run this script from a terminal window to start HamClock:

hamclock &

The first time that HamClock is run, some entries are requested. HamClock will also ask if you would like to connect to WiFi, Figure 8. Since you may have entered these for the Raspberry Pi operating system, you may answer yes if you would like to connect. HamClock will enter your username and password for you.

Figure 8. Connect to WiFi Screen. You will enter your call sign on setup page 1. You may provide your network username and password after saying yes to WiFi. If you provided these to the Raspberry Pi operating system, they will auto-fill if you select, yes. You can enter your latitude, longitude and grid square here, or you can Geolocate on your IP address (not recommended). Please click on image to expand.

Once the HamClock screen appears, if the correct resolution has been chosen, the screen should be mostly filled from top to bottom, but there may be some black bars on either side of the window. There are numerous instructions online about how to deal with this. I didn’t bother. Once I had chosen the closest resolution to my screen, 1366 x 768, I left well enough alone. HamClock also asks if you would like full-screen view, Figure 9, which eliminates the HamClock title bar as well as the taskbar. I selected that view.

Figure 9. Where to Select Full-Screen View. Full-screen view selection is on setup page 5. Please click on image to expand.

To close HamClock, please note that there is a small padlock symbol, Figure 10, beneath UTC in the upper left-hand corner. If one left clicks and holds the lock for a few seconds, then releases, a script will appear that will ask if you would like to exit the program. If you also intend to shut down the Pi, please don’t forget the logout procedure that is found under the Pi logo in the taskbar.

Figure 10. Padlock Symbol Beneath the UTC Box. If you were to left click and hold on the lock for a few seconds and release, a script will appear that will ask if you would like to exit HamClock. Please click on image to expand.

If you would like HamClock to start automatically upon reboot, a script that will do it may be run anytime from a terminal window. The scripts are found under, ” To install HamClock on other UNIX-like systems follow these steps”, in paragraph 10:

cd ~/ESPHamClock
mkdir -p ~/.config/autostart
cp hamclock.desktop ~/.config/autostart

You may want to place a HamClock icon on your Raspberry Pi desktop. That may be accomplished by copying, pasting and executing the following script in a terminal window:

cd ~/ESPHamClock
mkdir -p ~/.hamclock
cp hamclock.png ~/.hamclock
cp -p hamclock.desktop ~/Desktop

After running the scripts, close the terminal window and reboot the machine from the Pi icon. HamClock should restart immediately. The size of the HamClock window may appear reduced after reboot but may be expanded just as one might expand any other window.

As soon as HamClock is up and running you may want to explore all of the options and items that are found under “Terrain” that is found in the upper left-hand corner of the map, Figure 11. An extensive dropdown menu will appear. Go ahead and press the radio buttons followed by “okay” to see what happens. Every new screen is a surprise. It’s not that hard to get back to the screen where you started, so please experiment a little bit.

Figure 11. Dropdown Menu for the Main Graphic View. You will want to explore all of the options available from this dropdown menu visible to the left of the Mercator projection. Other menus may be accessed by clicking on the titles that appear within the smaller graphics. For a complete description, please consult the User Guide. Please click on image to expand.

Additional views for the smaller graphics may be requested by clicking on the graphics titles, themselves. For example, you may want to display propagation paths from your locale as supplied by WSJT, Figure 12. There are also satellite and space station orbits.

To change the color of your call sign background, click to the right of your call sign. To change the color of your call sign, click on the letters.

Figure 12. Display of Propagation Paths From Our Locale. If WSJT-X was selected on Page 2 of the setup menu, this graphic will be displayed. My call sign color and background color has been changed for this view. Please click on image to expand.

A particularly interesting view of the aurora is shown in Figure 13. This is one more example of how much data is available for presentation in Hamclock.

Figure 13.  Display of the Aurora. This is another example of how much data is available for display within the HamClock application. Please click on image to expand.

A complete HamClock User Guide is available at the Clear Sky Institute website under the User Guide tab[8].

Please let me know if you build a HamClock of your own. It is nice to receive feedback.

References:

[1] Elwood Downey, WB0OEW, HamClock, QST, October 2017, pp. 42-44.

[2] Raspberry Pi 4, Model B, 2 GB.

https://www.amazon.com/dp/B07TMGBPFQ/ref=sspa_dk_detail_6?ie=UTF8&pd_rd_i=B07TKFKKMPp13NParams&s=electronics&sp_csd=d2lkZ2V0TmFtZT1zcF9kZXRhaWxfdGhlbWF0aWM&th=1

[3] Raspberry Pi Zero (2017).

https://www.amazon.com/Raspberry-Pi-Zero-Wireless-model/dp/B06XFZC3BX/ref=sr_1_8?crid=2P2OQ2SF3LHR5&keywords=raspberry+pi&qid=1692662504&sprefix=Raspberry+pi%2Caps%2C151&sr=8-8

[4] Elwood Downey, WB0OEW, Clear Sky Institute. https://www.clearskyinstitute.com/ham/HamClock/

[5] Jason Oleham, KM4ACK, YouTube, 2:30. https://www.youtube.com/watch?v=2Cy5Swmk3gU

[6] Elwood Downey, WB0OEW, Clear Sky Institute, Op. Cit., Desktop tab.

[7] Jason Oleham, KM4ACK, YouTube, Op. Cit.

[8] Elwood Downey, WB0OEW, Clear Sky Institute, Op. Cit., User Guide tab.

 

 

 

Radio Amateurs Developing Skills Worldwide